Select Access® Smart™ FAQs

Q: Where can I find the instruction sheet of my Select Access Key Lock Box?

A:

-5441EURD Bluetooth Key Lock Box - Select Access® Smart - Wall Mount - Instruction Manual

Q: What is the product warranty?

Q: Where can I buy Master Lock products?

A:

You can find Master Lock products in most DIY stores, and in a selection of mass market stores, hardware stores, sporting good stores, web stores and professional resellers. See our Where to Buy section to find your nearest point of sales.

Q: How many locks or lock boxes can I add to my account?

A:

If you intend to assign access rights to more than 250 locks or lock boxes to an individual user, please first contact your Master Lock Sales Consultant or Master Lock Technical Support.

Q: What if my Select Access® Smart key lock box battery dies?

A:

If the battery dies while the lock box is closed, it can be unlocked using an external battery.

  1. If battery dies in locked position, locate battery jump contacts on the bottom of the lock box. (show illustration)
  2. Hold a new 9-volt battery underneath the lock box with the positive (+) and negative (-) terminals pressed against the jump contacts.
  3. While holding the battery in place, with an authorized mobile device within range of the lock box, press any keypad button on the lock box. If lock does not unlock, enter Primary Access Code on the lock box keypad.
  4. When lock box is opened, install a new CR123A battery.

Please note that after installing a new battery, the low battery icon will no longer display in the App after the lock box and App communicate with each other. However, it will take between 2 and 72 hours for the yellow LED to stop displaying on the lock itself.

For further help, please watch the video at the following link.

Q: How long will the batteries last on my Select Access® Smart key lock box?

A:

The battery should last at least 2 years under normal usage.

Q: The clear button on my Select Access® Smart key lock box is now yellow instead of blue or green. What is causing this?

A:

When the Select Access® Smart key lock box is low on power, you will be notified in three ways: an email notification, a warning in the App, and by a yellow light on the lock box.

To change the battery:

  1. Open the lock box door.
  2. With a flat head screwdriver, open the battery compartment located behind the door of the lock box.
  3. Remove the battery and replace it with a new CR123A battery. Make sure to position the positive and negative terminals properly, as indicated on the door of the battery compartment.
  4. Once installed close the battery door and tighten the screw.

Q: How do I open the Select Access® Smart key compartment?

A:

Master Lock Select Access® Smart can be opened using Bluetooth credentials or by entering a numeric code in the key pad.

To open using Bluetooth credentials:

  1. Make sure that the user has followed the instructions for "How to Register and Add Your Lock" or has accepted an invitation from a lock owner.
  2. Make sure that your Master Lock eLocks App is open and the user is logged in to the App.
  3. Wake the lock by pressing any key on the lock box key pad.
  4. When the lock lights green, open within 5 seconds.

To open using a traditional code:
The lock box can be opened using the primary code, a secondary code, or a temporary code, all of which are found in the App or distributed from the App.

  1. Enter the code into the lock box keypad.
  2. When the keypad lights green open the lock box by pulling on the door tabs.

Q: Can the Select Access® Smart key lock box be used outdoors?

A:

Select Access® Smart key lock box is designed to withstand outdoor environments.

Q: What is the product warranty for Select Access® Smart key lock box?

A:

The Select Access® Smart key lock box has a Limited Two (2) Year Warranty. Visit masterlock.eu for complete warranty details.

Q: What batteries does the Select Access® Smart key lock box use?

A:

Select Access® Smart key lock box comes with an installed C123A lithium battery.

Q: What if my phone battery dies? How can I access my Bluetooth Lock Box?

A:

If the phone's battery dies, the lock can be unlocked by entering the Primary Code, the current Temporary Code or the Backup Master Code on the lock keypad.

Q: What if my phone's Bluetooth isn't working to access my lock box?

A:

Make sure your phone is sufficiently charged. In phone’s settings, make sure that Bluetooth is turned on. If you can’t turn Bluetooth on, try restarting your phone and then re-launch the App.

Q: What phones are compatible with Select Access® Smart key lock box?

A:

Select Access® Smart key lock boxes are designed to work with devices that are built to Bluetooth v4.0 (or higher) specifications and implement the capability to communicate with Bluetooth Smart peripherals. iOS and Android platforms are currently supported. See Compatible Devices.

Q: How do I find the Activation Code in the lock box packaging?

A:

To locate the lock’s Activation Code on the instruction sheet included in the lock packaging:

  1. On the back of the package, locate the section that says OPEN HERE and cut along the scored, dotted line to allow access to the instruction sheet in the compartment behind the label.
  2. Open the compartment door and remove the folded instruction sheet.
  3. Locate the Activation Code in the gray box in the top left corner of the instruction sheet and enter it as instructed in the App.

Q: Are these locks susceptible to Bluetooth "hacking"?

A:

Master Lock utilizes Bluetooth Smart technology to facilitate wireless communication between locks and mobile devices. These locks and lock boxes are designed in a way that prevents the threat of Bluetooth hacking that exists with some other Bluetooth products. To provide leading-edge security, we employ robust, military-grade authentication and encryption mechanisms built upon proven, NIST recommended and FIPS Approved algorithms to deter sniffing, replay and manipulation attempts that Bluetooth technology has been associated with. These mechanisms are regularly audited by independent security professionals.

Q: Is it possible to update the firmware on the lock box?

A:

Yes, when a firmware update for your lock is available. You’ll be notified within the App whenever an update is available. You can also manually check for firmware updates by navigating to the ABOUT THIS LOCK page in the lock settings menu.

Q: Select Access® Smart key lock box will not re-lock. What should I do?

A:

This can occur if the door pins of the lock box are left resting against the lock mechanism without being closed. This has fooled the lock into thinking it is closed completely.

  1. Press any button on the lock keypad and when the lock lights green, close the lock and it will light blue when locked.
  2. If using a code to open the lock box, enter the key code provided, when the lock lights green, close the lock and it will light blue when locked.

Q: I replaced the battery in my lock box. Why does the lock LED still light yellow?

A:

After installing a new battery, the low battery icon will no longer display in the app, after the app and the lock communicate with each other. However, it will take between 2 to 72 hours for the yellow LED to stop displaying on the lock itself.

Q: What if my Guest does not have a Bluetooth enabled device to utilize the lock box?

A:

Your Guest can access the lock without a Bluetooth enabled device by entering a Manual Code on the lock keypad. To assign secondary code access with no expiration:

  1. If not already logged on, open the Master Lock Vault eLocks App and touch the appropriate lock box listed in the LOCKS list.
  2. Touch MANAGE LOCK in the upper right corner of the App.
  3. Scroll down to Secondary Codes and touch CHANGE SECONDARY CODES then follow the App instructions to add up to 5 secondary codes.

To assign a temporary code access with an expiration:

  1. If not already logged on, open the Master Lock Vault eLocks App and touch the appropriate lock box listed in the LOCKS list.
  2. Touch MANAGE LOCK in the upper right corner of the App.
  3. Touch the Settings Icon in the upper right corner of the App.
  4. Touch SHARE TEMPORARY CODES and then follow the App instructions to share current or future codes.

Q: How do I obtain an Activation Code for my Select Access® Smart key lock box?

A:

The Activation Code is provided with each lock or lock box in the upper left corner of the instructions. The instructions are included in the lock or lock box package.

If you have lost, or no longer have the instructions, please contact us

Q: Why do I need a Master Lock Vault account to register my lock box?

A:

The Master Lock Vault account ensures user credentials are securely deployed and provides enhanced functionality and convenience to the Master Lock Vault eLocks App.

Q: What if my phone is lost or stolen? What can I do?

A:

Reset Keys allows the lock box owner to revoke all Bluetooth® access to the lock, including their own. The owner and all guests will receive updated Bluetooth® credentials on their mobile devices.

LOST / STOLEN DEVICE NOTE! The owner of a lost or stolen mobile device should first go to the MasterLockVault.com web site and change their username and passcode.
To Reset Keys, the lock box owner must:

  1. Make sure that the owner's device that is synced to the lock is within Bluetooth® range of the lock box(Reset Keys cannot be performed remotely).
  2. Select the Appropriate padlock or lock box from the LOCKS list.
  3. Touch MANAGE LOCK in the upper right corner. Enter your passcode, if prompted.
  4. Touch the SETTINGS icon in the upper right corner.
  5. Touch RESET KEYS.
  6. Follow any additional instructions in the APP to save the changes to your lock box. This step must be completed for each lock box the lost or stolen device had access to.

Q: How do I accept an invitation to access a Select Access® Smart key lock box?

A:

The Select Access® Smart key lock boxes are designed so that the user can gain access using Bluetooth credentials using a smart phone or by using a traditional manual code entered into the key pad.

  1. The owner logs on to the Master Lock eLocks APP and follows the directions to ADD A GUEST, which results in an invitation being sent.
  2. Open the link in the invitation.
  3. Follow the prompts to either log into an existing Master Lock Vault account or create a new account.
  4. The host will receive an email confirmation that you have accepted the invitation.
  5. You will see the new lock under LOCKS SHARED WITH YOU in the APP and in their Master Lock Vault account.

Q: How do I revoke my lock box's access to a guest?

A:

To ensure a guest can no longer access a lock, the lock owner, should 1) Revoke Guest Access or Delete the Guest AND 2) Perform the RESET KEYS function within proximity of the lock.

  1. Under YOUR LOCKS, touch the lock for which you wish to remove a guest.
  2. Touch MANAGE LOCK in the upper right corner. Enter your passcode, if prompted.
  3. Swipe the guest record to the left.
  4. Touch the DELETE icon.
  5. Select REVOKE ACCESS (to revoke the guest's access to this lock only) or DELETE (to delete the guest from all locks).
  6. Your guest will receive an email notification that their access has been revoked.
  7. Make sure that the owner’s device that is synced to the lock is within proximity of the lock (reset keys cannot be performed remotely).
  8. Select the lock from the LOCKS list.
  9. Touch MANAGE LOCK in the upper right corner. Enter your passcode, if prompted.
  10. Touch the SETTINGS icon in the upper right corner.
  11. Touch RESET KEYS.
  12. Follow any additional instructions in the APP to save the changes to your lock. This step must be completed for each lock in instances where there is a lost or stolen device.

Q: How do I add a guest to my Select Access® Smart key lock boxes?

A:

You can share access to your lock with friends, family or colleagues.
To provide Bluetooth access:

  1. To enable your guests to access your lock box, open the Master Lock Vault eLocks APP.
  2. Select the lock to which you would like to provide guest access from the Locks list.
  3. Touch MANAGE LOCK in the upper right corner. Enter your passcode, if prompted.
  4. Scroll down to GUESTS and touch the ADD A GUEST icon in the upper right corner.
  5. Select the Appropriate option to choose an existing guest or add a new guest.
  6. Follow the prompts to enter your guest's contact information and then touch CONTINUE
  7. Select your guests’ schedule: UNLIMITED (24/7), DAY (7 am to 7 pm), or NIGHT (7 pm to 7 am)
  8. Touch SEND INVITATION
  9. You will receive a confirmation that an invitation has been sent.
  10. Once your guest opens the link in their invitation, they will be prompted to either log into their Master Lock Vault account or create a new account.
  11. You will receive an email confirmation that they have accepted the invitation.
  12. Your guest will see your lock under LOCKS SHARED WITH YOU in their APP and in their Master Lock Vault account.

Q: Do I need a pin or key card to access my lock box?

A:

The Select Access® Smart key lock box has been designed for ease of use and security. When opening with BLE credentials through the Master Lock Vault eLocks APP, no pin code or key card is needed. Primary and secondary codes are only used as an alternative form of entry.

Q: Where can I find the Master Lock Vault eLocks app?

A:

The app is available in the Apple App Store and the Google Play Store. Click below or search for "Master Lock Vault eLocks" in the app stores.


Download on the Apple App Store Android App on Google Play